Section Contents

Moisture Content: Use Classes and Relevant Service Classes

For maximum biological durability, both Service Classes and Use Classes must be considered when specifying US CE-marked panels .  This guide helps you make the right selection.

There are no longer ‘hazard classes’ for different products.  This has been replaced (see updated EN 335:2013) by Use Classes covering plywood and OSB.  They will also cover LVL when the LVL standards have completed their current update.

Use Classes are based on different environmental exposures that can make the panel susceptible to deterioration. , as given in Eurocode 5, are used for assigning  strength values and calculating deformation in load bearing situations.  They are determined by the moisture content of the panel corresponding to the environmental humidity and temperature during service. More

For Use Class 1 situations below – refer to Service Class 1 or Service Class 2

  • Situations in which the wood or wood-based product is inside a construction, not exposed to the weather and wetting.
  • Attack by disfiguring fungi or wood-destroying fungi is insignificant and always accidental.
  • Attack by wood-boring insects, including termites, is possible although the frequency and importance of the insect occurrence depends on the geographical region.

For Use Class 2  situations – refer to Service Class 2 or Service Class 3

  • The  component could be subject to occasional wetting caused by e.g. condensation.
  • The wood or wood-based product is under cover and not exposed to the weather, particularly rain and driven rain, but where occasional, but not persistent, wetting can occur. Condensation of water on the surface of wood and wood-based products may occur.
  • Attack by disfiguring fungi and wood-destroying fungi is possible.
  • Attack by wood-boring insects, including termites, is possible although the frequency and importance of the insect risk depends on the geographical region.

For Use Class 3 situations – refer to Service Class 3 

  • Minimum requirement for external use
  • Situations in which wood or wood-based product is above ground and exposed to the weather, particularly rain.
  •  Attack by disfiguring fungi and wood-destroying fungi is possible.
  • Attack by wood-boring insects, including termites, is possible although the frequency and importance of the insect risk depends on the geographical region.
  •  Use Class 3.1: In this situation the wood and wood-based products will not remain wet for long periods. Water will not accumulate.
  • Use Class 3.2: In this situation the wood and wood-based products will remain wet for long periods. Water may accumulate.

Service Class 1: moisture content in the material corresponding to a temperature of 20°C and the relative humidity of the surrounding air only exceeding 65% for a few weeks per year. The average moisture content in most softwoods will not exceed 12%.

Service Class 2: moisture content in the material corresponding to a temperature of 20°C and the relative humidity of the surrounding air only exceeding 85% for a few weeks per year.  The average moisture content in most softwoods will not exceed 20%.

Service Class 3: characterised by climatic conditions leading to higher moisture content than in Service Class 2.

Use Classes for plywood in Annex B of EN 636:2012+A1:2015.When selecting the Use Class for plywood, performance may be compromised if suitable preservative treatment and/or relevant surface and edge coating is not applied and if the panels are not properly maintained and installed.

For LVL – refer to the plywood text in EN 335-3.

For plywood and LVL, guidance on factors affecting durability can also be found in DD CEN/TS 1099.

 

APA in Europe Wizard

Close
All Questions OSBPlywood

What is a ‘life cycle stage’ and how do these link to the environmental assessment of whole buildings?

How do core category rules link with environmental product declarations?

Whose responsibility is it to check that wood products being imported into the EU do not originate from illegally sourced timber supplies?

Does the EUTR require mills to provide any extra documentation for customs entry into the European Union?

Must all plywood and OSB panels carry a CE marking?

What is the definition of a construction product under the CPR?

What is a Declaration of Performance referred to under the Construction Products Regulation?

What is the difference between Structural 1 and Exposure 1?

Does structural panel siding have shear values?

What are mould and mildew, and do they compromise the integrity of engineered wood?

The CE-mark on an APA plywood panel means it conforms to European Standards – but which ones?

I want to use a Rated Sheathing panel for flooring/ roofing application, what info do I need to know?

Plywood: Span rating
OSB: Span rating

What extra strength benefits do Structural 1 OSB panels provide over standard Rated Sheathing panels?

Do APA panels give off formaldehyde?

Plywood: Formaldehyde
OSB: Formaldehyde

What is the difference between a touch-sanded panel and sanded panel?

I’d like to know how APA veneer grades match those given in the European standards

How do I correctly gauge the face appearance a plywood Siding panel?

I want to specify an APA panel for concrete formwork – what do I need to know?

Are APA panels tongue and grooved on all four edges?

I am not familiar with the term ‘Sized for Spacing’ – what is its significance?

How are Performance Category and thickness related?

I’d like to know more about a panel’s Span Rating and how it links to thickness.

Plywood: Span rating
OSB: Span rating

What is Span Rating on the APA trademark and why is it important?

Plywood: Span rating
OSB: Span rating

What is the difference between Exposure 1 and Exterior plywood panels? What are their appropriate uses?

What are the main OSB panels likely to be available in Europe?

What are the main plywood panels likely to be available in Europe?

What are the main European standards that I would need to be aware of for OSB panels?

The main standards are: EN 13986 and EN 300

What are the main European standards that I would need to be aware of for plywood panels?

The main standards are: EN 13986, EN 636, EN 314, EN 635-3