Section Contents

 Veneer Grades

Veneer in a finished US trademarked plywood panel must conform to one of the six grades listed in the US PS 1-09 standard: N, the highest classification (rarely produced), followed by A, B, C-plugged, C and D.

See veneer grades for Popular APA Plywood Panels.

The requirements given here apply to panels measuring 2440mm (96”) x 1220mm (48”) and are proportionate for other sizes.

APA has produced two easy to follow guides to help match the grade numbers given on a US finished plywood panel with the requirements of  EN 635-3.

Detailed guide (below) listing permissible defects – with maximum sizes.

Simplified guide to the US PS 1-09 veneer grading rules and appearance grades in EN 635-3 based on the appearance of the surface veneers. Equivalents cannot be exactly compared as two different sets of grading rules apply.

Veneer Grade Description Permissible defects  – maximum sizes

N

(rarely produced)

Should be smoothly cut and be either 100% heartwood or 100% sapwood, free from knots, knot holes, pitch pockets, open splits, other open characteristics and stain.  The veneer must consist of not more than two pieces in 1220 mm (48”) widths and not more than three pieces in wider panels; and be well matched for colour and grain.  When panels are sanded no sander skips are permitted.

A

Must be firm, smoothly cut and free from knots, pitch pockets, open splits and other open characteristics.  If consisting of more than one piece, they must be well jointed.  When panels are sanded, no sander skips are permitted.
Knots Not allowed
Open knots/holes Not allowed
Splits Not allowed
Grain Smooth
Repairs May be a max of 18 wood parallel to the grain or synthetic

B

Must be solid and free from open characteristics and broken grain, except as permitted e.g. where there are knots or splits.
Knots 25.4mm (1”).  Must be sound & tight
Open characteristics 1.6mm (1/16”)
Splits 0.8 mm (1/32”)
Repairs permitted (unlimited) wood or synthetic
Sander skips permitted up to 5% of panel

C

Tight knots Up to 38.1mm (1-1/2”) no limit
Knot/ open holes 25.4mm (1”) max. With an occasional up to 38.1 mm (1-1/2”) across grain
Splits Measured at 203mm (8”) from panel end – not to exceed 12.7mm (1/2”) in width by ½ panel length, or 9.5mm (3/8”) width by any panel length, provided separation at one end no greater than 1.6 mm (1/16”)
Repairs Permitted in wood or synthetic
Discolouration Permitted

C-plugged

Improved C veneer
Open 6.4 mm (1/4”) x 12.7mm (1/2”)
Tight knots Up to 38.1mm (1-1/2 “)
Splits Limited to 3.2mm (1/8”) width
Broken grain Permitted but limited
Repairs Synthetic and wood permitted
Touch sanded may be fully sanded

D

Knots Up to 63.5mm (2-1/2”) width across grain.  Occasional tight knot up to76.2mm (3”)
Open knots/ holes Up to 63mm (2-1/2”) width across grain
Splits Measured at 203mm (8”) from panel end, not to exceed 25.4mm (1”) tapering to not more than 1.6mm (1/16”) where running full panel length. Splits on panel faces 6.4mm (1/4”) width where located within 25.4mm (1”) of parallel panel edge.
Broken grain Permitted
Wane When not exceeding 203mm (8”) length width of wane may be up to 76.2mm (3”) pending location in panel.
D Grade veneers are not permitted in Exterior grade panels

veneer grading rules and appearance grades in EN 635-3 based on the appearance of the surface veneers.

 US PS 1-09 Standard

 EN 635-3 (Softwood)

N
A
B
C plugged
C
D

E
I
I/II
II/III
III
IV

APA in Europe Wizard

Close
All Questions OSBPlywood

What is a ‘life cycle stage’ and how do these link to the environmental assessment of whole buildings?

How do core category rules link with environmental product declarations?

Whose responsibility is it to check that wood products being imported into the EU do not originate from illegally sourced timber supplies?

Does the EUTR require mills to provide any extra documentation for customs entry into the European Union?

Must all plywood and OSB panels carry a CE marking?

What is the definition of a construction product under the CPR?

What is a Declaration of Performance referred to under the Construction Products Regulation?

What is the difference between Structural 1 and Exposure 1?

Does structural panel siding have shear values?

What are mould and mildew, and do they compromise the integrity of engineered wood?

The CE-mark on an APA plywood panel means it conforms to European Standards – but which ones?

I want to use a Rated Sheathing panel for flooring/ roofing application, what info do I need to know?

Plywood: Span rating
OSB: Span rating

What extra strength benefits do Structural 1 OSB panels provide over standard Rated Sheathing panels?

Do APA panels give off formaldehyde?

Plywood: Formaldehyde
OSB: Formaldehyde

What is the difference between a touch-sanded panel and sanded panel?

I’d like to know how APA veneer grades match those given in the European standards

How do I correctly gauge the face appearance a plywood Siding panel?

I want to specify an APA panel for concrete formwork – what do I need to know?

Are APA panels tongue and grooved on all four edges?

I am not familiar with the term ‘Sized for Spacing’ – what is its significance?

How are Performance Category and thickness related?

I’d like to know more about a panel’s Span Rating and how it links to thickness.

Plywood: Span rating
OSB: Span rating

What is Span Rating on the APA trademark and why is it important?

Plywood: Span rating
OSB: Span rating

What is the difference between Exposure 1 and Exterior plywood panels? What are their appropriate uses?

What are the main OSB panels likely to be available in Europe?

What are the main plywood panels likely to be available in Europe?

What are the main European standards that I would need to be aware of for OSB panels?

The main standards are: EN 13986 and EN 300

What are the main European standards that I would need to be aware of for plywood panels?

The main standards are: EN 13986, EN 636, EN 314, EN 635-3